٭٭٭خانزورلڈ ميں خوش آمديد٭٭٭آپ کےلئے اردو اور انگلش کى منفرد ويب سائيٹ٭٭٭جس ميں مختلف قسم کى معلومات فراھم کى گئ ھيں٭٭٭ جس ميں شامل ھيں اسلام, سکول, کمپيوٹر, آڈيو ويڈيو, تصاوير, گيمز, طنزومزاح اور اس کے علاوه بهت کچه .........!٭٭٭
MOBILE SECRET CODES HOME
SIEMENS SECRET CODES |
|
SIEMENS S1 / S3 / S3 COM / S4 To view the software date and else with S3 com, S4, S4Power press with SIM removed *#06# and left softkey. To view some other stuff with S4Power press with SIM removed *#06# and left softkey twice. To view the software date with S3 com, S4, S4Power press with SIM installed menu 98 and left softkey twice. ACTIVATE MONITOR MODE Siemens S1/S3 Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button (left MENU key), 5553756, HangUp Button (Red HandSet key) Siemens S3 COM/S4 Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button (left MENU key), 7684666, HangUp Button (Red HandSet key) Note: Now Monitor should appear at the bottom of the Network Options menu. MONITOR MODE Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals. Test Mode Indicators: (* = only available when call in progress ) CH Channel Number RX Signal Strength (dB) N NCC (Colour Code) B BCC (Colour Code) CI Cell ID (in Hex) C1+ How long before phone does forced hand over.(see RX and RXAM) LAI Location Area Identity. Display Network ID code(42F010 = 240.01) and MSC TXPWR Transmit Power (dB) RXAM Receive signal strength cut-off point TS* Time Slot Number TA* Timing Advance. Distance from tower in Km X 2 PL* Power Level SIEMENS S1 Here's a trick to play Tetris, also known as Klotz on a Siemens S1. Turn the phone on. Enter PIN. Before the telephone has logged in to the your GSM net do the following steps. 1: Choose F 9 (function settings) 2: Choose send own number and push the right button for choose. 3: Push 9 USE 2 as < and 8 as > , rotate the klotz with 5 and drop with 4. I have just heard from one of the programmers of the phone that Tetris was in the phone during development, but it was removed before it was produced. Apparantly someone has the patent on games in mobile phones and Siemens didn't want to pay the licensing fees. It was either in Menu F-9-9 or it's not there at all. GO TO TOP |
|
Secret Codes SP unlock *#0003*(secret code 8 digits)# *#06# for checking the IMEI (International Mobile Equipment Identity) Resets language to automatic selection : * # 0000 # then Green button Pin Out 1- GND 2- SB 3- POWER 4- NC 5- TX 6- RX 7- CLOCK 8- DATA 9- GND MIC 10- HF MIC 11- AUDIO 12- GND AUDIO |
|
Secret Codes SP unlock *#0003*(secret code 8 digits)# *#06# for checking the IMEI (International Mobile Equipment Identity) Tetris Power on phone and enter PIN. before phone has locked onto network, F9, send own number, hit right button, hit 9. left is 2, right is 8, rotate is 5, and drop is 4. Monitor Mode 1. Menu 2. 9 (Phone Options) 3. 7 (Phone Status) 4. Left Display Button (left MENU key) 5. 5553756 6. HangUp Button (Red HandSet key) Now "Monitor" should appear at the bottom of the Network Options menu. Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals. Test Mode Indicators: (* = only available when call in progress ) CH Channel Number RX Signal Strength (dB) N NCC (Color Code) B BCC (Color Code) CI Cell ID (in Hex) C1+ how long before phone does forced hand over. (see RX and RXAM) LAI Location Area Identity. Display Network ID code (42F010 = 240.01) and MSC TXPWR Transmit Power (dB) RXAM Reeceive signal strength cut-off point TS* Time Slot Number TA* Timing Advance. Distance from tower in Km * 2 PL* Power Level Power Table PL: 5 6 7 8 9 10 11 12 13 14 15 dB: 33 31 29 27 25 23 21 19 17 15 13 Watts: 2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02 LF* C1 value with continuous transmisson from tower LS* C1 Value with discontinuous tranmission from tower QF* Bit Error Rate with continuous transmission from tower QS* Bit Error Rate with discontinuous transmission from tower BER (bit error rate) table QF/QS register: 0 1 2 3 4 5 6 7 % of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6 Tips and tricks Nice Sunset in the display. Siemens S3 or younger In the Telephone Book in the section own numbers, first position you have to type in +12022243121 (Number of the Capitol in Washington DC) and save it without a name. Then open this telephone book again do so as you like to change the number but leave the modus without changing anything. A nice Sundown will be shown in the display. Pin Out 1- GND 2- SB 3- POWER 4- NC 5- TX 6- RX 7- CLOCK 8- DATA 9- GND MIC 10- HF MIC 11- AUDIO 12- GND AUDIO GO TO TOP |
|
Secret Codes SP unlock *#0003*(secret code 8 digits)# *#06# for checking the IMEI (International Mobile Equipment Identity) Tetris Power on phone and enter PIN. before phone has locked onto network, F9, send own number, hit right button, hit 9. left is 2, right is 8, rotate is 5, and drop is 4. Monitor Mode 1. Menu 2. 9 (Phone Options) 3. 7 (Phone Status) 4. Left Display Button (left MENU key) 5. 5553756 6. HangUp Button (Red HandSet key) Now "Monitor" should appear at the bottom of the Network Options menu. Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals. Test Mode Indicators: (* = only available when call in progress ) CH Channel Number RX Signal Strength (dB) N NCC (Color Code) B BCC (Color Code) CI Cell ID (in Hex) C1+ how long before phone does forced hand over. (see RX and RXAM) LAI Location Area Identity. Display Network ID code (42F010 = 240.01) and MSC TXPWR Transmit Power (dB) RXAM Reeceive signal strength cut-off point TS* Time Slot Number TA* Timing Advance. Distance from tower in Km * 2 PL* Power Level Power Table PL: 5 6 7 8 9 10 11 12 13 14 15 dB: 33 31 29 27 25 23 21 19 17 15 13 Watts: 2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02 LF* C1 value with continuous transmisson from tower LS* C1 Value with discontinuous tranmission from tower QF* Bit Error Rate with continuous transmission from tower QS* Bit Error Rate with discontinuous transmission from tower BER (bit error rate) table QF/QS register: 0 1 2 3 4 5 6 7 % of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6 Unlock Siemens S3(Not S3 COM) (For advanced users only) At addresses 0D8 to 0DD the phones code is stored. To read the code swap nibbles stored at addresses from 0DA to 0DD. Error counter is at 0D9. To clear the Phone Code write at addresses from 0D8 to 0DD: 00, 00, FF, FF, FF, FF. Siemens S3 comfort Show IMEI code: * # 06 # MONITOR MODE The Siemens S3 Com series have a Monitor mode that can be activated directly from the standard user keypad. In order to activate this mode, you must enter the special access code currently programmed into the phone. TO ACTIVATE MONITOR MODE 1. Turn the phone on. 2. Enter the PIN access code on press OK. (Only if is enabled). 3. Press Menu. (Left top button). 4. Press 9. (Phone Options). 5. Press 8. (Phone Status) (May be button 7 in some phones). 6. You may see your IMEI Number 7. Left Display Button (Top left MENU key). 8. 7684666 9. HangUp Button. (Red HandSet key). Note: Monitor should appear now at the bottom of the Network Options menu. MONITOR MODE TOGGLE Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes Tips and tricks Nice Sunset in the display. Siemens S3 or younger In the Telephone Book in the section own numbers, first position you have to type in +12022243121 (Number of the Capitol in Washington DC) and save it without a name. Then open this telephone book again do so as you like to change the number but leave the modus without changing anything. A nice Sundown will be shown in the display. Pin Out 1- GND 2- SB 3- POWER 4- NC 5- TX 6- RX 7- CLOCK 8- DATA 9- GND MIC 10- HF MIC 11- AUDIO 12- GND AUDIO |
|